Back
MOCKED EXAMS NEXT-GEN LABS

13 INNOVATIVE VISUAL LABSALL 13 LIVE

13-FEATURE VISUAL ENGINEERING & REVISION SUITE

Interactive Hardware, Safety Signs, Physics & Psychometric Sims

Every visual component engineered specifically for UK electrotechnical and construction qualifications. Test real tester faceplates, review BS EN ISO 7010 safety signs, inspect bathroom IP zones, scale conductor physics, flip BS 7671 Brown Book pages, and outsmart examiner traps.

VISUAL 1 OF 10HARDWARE SKEUOMORPHIC

Photorealistic MFT Faceplate

Tactile rotary dial, 7-segment digital backlit LCD with BS 7671 pass/fail verification

BS 7671 Part 6 / Reg 643
MFT-1845 PRO
MULTIFUNCTION INSTALLATION TESTERCAT IV 300V
LOOP_ZSREADY (BS 7671)BAT: 100%
0.38Ω
PFC/SEC:618A PFC
STATUS:PASS
REGULATION CHECK: Max Zs for 32A Type B MCB = 1.10 Ω (Reg 411.3.2) - PASS
No-Trip Earth Fault Loop Impedance (Zs / Ze)
L1 (RED)
L2 / N (BLUE)
PE (GREEN)
VISUAL 2 OF 10ELECTRICAL PHYSICS

Live Animated Cable Cross-Section

Dynamic physical conductor scaling, insulation layers, current capacity & volt drop

BS 7671 Table 4D5 & Appendix 4

CABLE CROSS-SECTION INSPECTOR

BS 7671 Table 4D5 & Appendix 4 Conductor Geometry & Thermal Sizing

L (Brown)CPCN (Blue)
Hover over any insulation layer, sheath, or copper core to inspect specification.
SELECT CONDUCTOR CROSS-SECTIONAL AREA (CSA):
2.5 mm²
Current Rating (Iz)
27 A
Method C (Clipped)
Volt Drop (mV/A/m)
18
BS 7671 Tab 4D5
Typical OCPD
32A Ring / 20A Radial
BS EN 60898
CPC Size
1.5 mm²
Earth Conductor
Typical Site Application: 32A Socket Outlet Ring Final Circuits (RFC) & 20A radials.
VISUAL 3 OF 10HARDWARE SKEUOMORPHIC

Neon Proving Unit Glow Micro-Interactions

Authentic high-voltage neon gas strike ionization animation with GS38 test wand

HSE Guidance Note GS38

NEON PROVING UNIT & VOLTAGE INDICATOR

400V
230V
120V
50V
12V
GS38 CAT IV
PROVING UNIT (PU500):
STANDBY - READY FOR PROVE
PRACTICE INTERACTION QUESTION:

According to HSE Guidance Note GS38, what is the maximum exposed conductive tip dimension for test probes?

VISUAL 4 OF 10ELECTRICAL PHYSICS

Interactive 3D / Isometric Consumer Unit

Non-combustible metalclad distribution board with flip RCBOs, SPD & busbar cutaway

BS 7671 Reg 421.1.201 / BS EN 61439-3

INTERACTIVE CONSUMER UNIT CUTAWAY

BS 7671 Reg 421.1.201 Non-Combustible Metalclad Board with Type 2 SPD & RCBOs

BS EN 61439-3|100A INCOMING|IP2XC ENCLOSURE
EARTH BAR (MET)
NEUTRAL BAR
100A MAIN
DP SWITCH
LIVE
SPD T2
40kA
OK
SPD
Type 2
C1
B6
C2
B6
C3
B32
C4
B32
C5
B40
C6
B32
INSULATED COPPER COMB BUSBAR (100A RATED)Click to Inspect
CIRCUIT SCHEDULE & LOADS:
SPDSurge Protection
ENERGIZED
C1Ground Floor Lights
ENERGIZED
C2First Floor Lights
ENERGIZED
C3Kitchen Ring Final
ENERGIZED
C4Lounge Sockets
ENERGIZED
C5Electric Shower (9.5kW)
ENERGIZED
C67.4kW EV Fast Charger
ISOLATED
VISUAL 5 OF 10EXAM PSYCHOLOGY

Dynamic Exam Pressure Pulse Meter

Biometric cardiac pacing tachometer shifting calm teal → amber → blood-red pulse

C&G 2382 / 2391 Time Management

EXAM PRESSURE & TIME PACE GAUGE

Dynamic biometric psychological pacing HUD

CRITICAL HIGH PRESSURE (<20% TIME)
12:00TIME REMAINING20% Budget
TARGET PACE METRIC:
1.5minutes / question
Based on 8 unanswered exam questions.
TACTICAL STRATEGY:
Emergency Time Protocol: Never leave any question blank! Mark your best instinct, eliminate 2 distractors, and do not spend more than 45s on complex calculations.
DRAG TO SIMULATE REMAINING TIME:12.0 / 60 min
Questions Left:
VISUAL 6 OF 10SECURITY & IDENTITY

CSS 3D Holographic CSCS Smart Card

Real-time mouse tilt physics, EMV gold microchip, and iridescent rainbow foil

CITB / CSCS / ECS Verification

3D HOLOGRAPHIC SMART CARD PREVIEW

Real-time optical foil tilt physics with embedded smart microchip

UK CONSTRUCTION LICENCE
Electrotechnical Certification Scheme (ECS)
CSCS SECURE
JAY M. HARRISON
REG: 04829104 / EXP: 09/2031ECS ELECTRICIAN
VERIFIED OCCUPATION & NVQ:
C&G 2365 Level 3 Diploma in Electrical Installations + AM2
CPD & Health, Safety and Environment Certified
||| | |||| | ||||| |||
CITB / JIB SECURE ID
NFC CHIP ACTIVE
CUSTOMIZE CARD EMBOSSING:
VISUAL 7 OF 10ELECTRICAL PHYSICS

Earthing System Current Flow Schematics

Interactive animated TN-S, TN-C-S PME & TT loops with earth fault simulation

BS 7671 Chapter 31 & Table 41.2

EARTHING ARRANGEMENTS & CURRENT FLOW

BS 7671 Part 3 System Characteristics & Fault Loop Impedance Zs

11kV / 400VSUBSTATIONSTAR NCONSUMERAPPLIANCE / METCLASS I LOADLine (L - 230V)Neutral (N)PEN Conductor (Neutral + Earth)
FAUT SIMULATION:✓ HEALTHY NORMAL OPERATION
MAX PERMISSIBLE Ze
0.35 Ω (Lowest typical impedance in UK housing)
BS 7671 Table 41.2
PROSPECTIVE FAULT CURRENT (Ipf)
Very High (typically 1.5 kA - 6.0 kA)
Ipf = U0 / Zs
REQUIRED PROTECTION
Fast magnetic trip on MCB (0.4s standard)
Reg 411.3.2
TN-C-S (PME) SYSTEM: The supply combines neutral and earth into a single PEN (Protective Earth & Neutral) conductor. Multiple earth electrodes along the DNO network anchor the potential. Neutral & Earth split at the cutout.
VISUAL 8 OF 10HARDWARE SKEUOMORPHIC

Site Rugged Skeuomorphic Theme Mode

Heavy-duty rubberized matte chassis, caution hazard stripes, and high-visibility nits

MIL-STD 810G Outdoor Contrast

SITE RUGGED SKEUOMORPHIC THEME

Heavy-duty site-proof high-visibility layout designed for outdoor daylight and tablets

QUESTION 18 / 60BS 7671 SECTION 701
94% 4G LTE

Within Zone 1 of a location containing a bath or shower, what is the minimum required Ingress Protection (IP) rating for installed electrical equipment?

AIPX4 (or IPX5 if water jets are used for cleaning)
BIP2X (standard finger protection only)
CIP68 (continuous underwater submersion required)
OUTDOOR SUNLIGHT POLARIZER MODE
MIL-STD 810G
Impact Resistant UI
GLOVE-FRIENDLY
48px Tap Targets
SOLAR-SPEC
Max Luminance 1000 Nits
VISUAL 9 OF 10HARDWARE SKEUOMORPHIC

BS 7671 "Brown Book" Virtual Page Flip

3D book turn with fluorescent yellow highlighter sweeping over high-frequency clauses

BS 7671:2018+A4:2026 IET Brown Book

BS 7671 "BROWN BOOK" VIRTUAL READER

IET Wiring Regulations 18th Edition: A4:2026 with Interactive Highlighter

BRITISH STANDARD BS 7671:2018+A4:2026
Part 4: Protection for SafetyPAGE 58
REGULATION 411.3.2.2

Automatic Disconnection of Supply - TN Systems

In a TN system, the maximum disconnection time stated in Table 41.1 shall apply to final circuits not exceeding 32 A and supplying: (i) socket-outlets, and (ii) other equipment. For nominal voltage U0 of 230 V AC to earth, the maximum disconnection time shall not exceed 0.4 seconds.
EXAM STRATEGY NOTE:
High-frequency exam question! Remember: 0.4s for TN systems <= 32A; 0.2s for TT systems; 5.0s for distribution circuits > 32A.
1 of 4 High-Yield Clauses
VISUAL 10 OF 10EXAM PSYCHOLOGY

Question Difficulty Heatmap & Trap Overlay

Candidate distractor distribution thermal bars and examiner trap deconstruction

Psychometric Distractor Analysis

QUESTION TRAP HEATMAP OVERLAY

Real-time candidate response distribution & distractor trap analysis

TRAP RISK LEVEL: HIGH (48% FAILURE RATE). Only 38% of candidates answer this correctly on first attempt.
C&G 2391 / 2382 PRACTICE EXAMINATION

When carrying out an on-site initial verification test at ambient temperature (20°C) on a 32 A Type B MCB circuit, what is the maximum measured earth fault loop impedance (Zs) permissible to satisfy BS 7671 Regulation 411.3.2?

A1.10 Ω (Calculated using Tabulated Table 41.3 without rule-of-thumb temperature correction)
TRAP48%
B0.88 Ω (Table 41.3 value of 1.10 Ω multiplied by 0.8 rule-of-thumb factor for ambient test)
38%
C1.44 Ω (Using standard Cmin 0.95 without temperature derating)
10%
D0.40 Ω (Confusing standard TN-S disconnection time with resistance)
4%
EXAMINER TRAP DECONSTRUCTION:C&G Item Writing Standard

CLASSIC EXAMINER TRAP: 48% of candidates take the raw uncorrected Table 41.3 value (1.37Ω) or forget to multiply by the 0.8 factor (1.10Ω) required when testing at ambient conductor temperatures on site (Appendix 3 / Table B6).

False Confidence Index: 76% of candidates felt certain Option A was right.Rule of Thumb: Tabulated x 0.8
VISUAL 11 OF 10SAFETY & SIGNS

BS EN ISO 7010 Safety Signs & Extinguishers

Mandatory, Warning, Prohibition & Emergency sign gallery with fire extinguisher electrical matrix

BS EN ISO 7010 / Safety Signs Regs 1996

SAFETY SIGNS & STATUTORY NOTICES REVISION

BS EN ISO 7010 & BS 7671 Chapter 51 Identification, Warning Notices & Fire Extinguisher Guide

⚡
Danger: Electricity / High Voltage
BS EN ISO 7010 W012
🔋
Caution: Battery Charging Hazard
BS EN ISO 7010 W026
🏗️
Danger: Overhead Electric Power Lines
BS EN ISO 7010 W029
💥
Warning: Arc Flash Hazard
BS EN ISO 7010 W042
🥽
Eye Protection Must Be Worn
BS EN ISO 7010 M004
🔒
Lock Out & Danger Tag Before Commencing Work
BS EN ISO 7010 M005
🥾
Safety Footwear Required
BS EN ISO 7010 M008
🚫
Do Not Switch On - Men Working on Circuit
BS EN ISO 7010 P014
💧
Do Not Extinguish with Water
BS EN ISO 7010 P006
🛑
No Unauthorised Access to Electrical Plant
BS EN ISO 7010 P001
🚨
Emergency Power Off (EPO) / Break Glass Switch
BS EN ISO 7010 E008
🩹
First Aid Station & Electric Shock Resuscitation
BS EN ISO 7010 E003
BS EN ISO 7010 W012WARNING
⚡

Danger: Electricity / High Voltage

Equilateral Triangle with Yellow Background and Black Border/Symbol

STATUTORY MEANING:
Warns of lethal electrical voltage (230V, 400V 3-phase, or high voltage sub-station equipment).
TYPICAL SITE LOCATION:
Distribution boards, switchgear enclosures, busbar chambers, substation doors.
EXAM QUESTION ANATOMY:
Examiner trap: Warning signs warn of a hazard (Yellow). Do NOT confuse with Prohibition (Red) or Mandatory (Blue).
Standard: BS EN ISO 7010 / Safety Signs and Signals Regs 1996C&G 2365 Unit 201 & AM2 Tested
VISUAL 12 OF 10ELECTRICAL PHYSICS

Bathroom Zones & Ingress Protection (IP Codes)

BS 7671 Section 701 Special Locations cutaway with 2-digit solid/liquid IP code decoder

BS 7671 Section 701 & BS EN 60529

BATHROOM ZONES & IP CODES DECODER

BS 7671 Section 701 Special Locations & BS EN 60529 Ingress Protection Matrix

Finished Floor Level (0.00m)2.25m Datum BoundaryZONE 0 (IPX7)ZONE 1 (IPX4)ZONE 2 (IPX4)0.60m WidthOUTSIDE ZONES13AMin 2.5m from Zone 1
ZONE 1 (Above Bath/Shower Basin to 2.25m)Minimum: IPX4 minimum (or IPX5 if water jets are used, e.g. for cleaning in public/communal showers)

Vertically above the bath or shower basin up to 2.25m from the finished floor level, or to the highest fixed shower head (whichever is higher).

Voltage & Protection Rules: Equipment must be SELV or PELV (≤ 25V AC / 60V DC), or 230V equipment specifically permitted by manufacturer and protected by 30mA RCD.
EXAM STRATEGY CUE:

Amendment 2/3 check: All circuits serving OR passing through a location containing a bath or shower must have 30mA RCD protection (Reg 701.411.3.3)!

INTERACTIVE IP CODE DECODER (BS EN 60529)

IP24
FIRST NUMERAL: SOLIDS (0 - 6)IP2X
IP2X: Protected against solid objects > 12.5 mm (standard finger protection for consumer units).
SECOND NUMERAL: LIQUIDS (0 - 8)IPX4
IPX4: Protected against splashing water from any direction (Standard for Bathroom Zone 1 & 2).
VISUAL 13 OF 10ELECTRICAL PHYSICS

Cable Colour Harmonisation & Loft Methods (Ci)

Pre-2004 vs modern harmonised colour cross-reference and thermal loft insulation derating factors

BS 7671 Table 51 & Appendix 4

WIRING COLOUR HARMONISATION & INSTALLATION METHODS

BS 7671 Table 51 Harmonised Conductor Identification & Appendix 4 Reference Methods

SELECT SUPPLY CONFIGURATION:
HISTORIC UK STANDARD (PRE-2004)BS 7671:2001
Phase 1 (L1)
RED
Phase 2 (L2)
YELLOW
Phase 3 (L3)
BLUE
Neutral (N)
BLACK
Protective Earth (CPC)
GREEN / YELLOW
HARMONISED STANDARD (2004 - PRESENT)BS 7671:2018+A4:2026
Phase 1 (L1)
BROWN
Phase 2 (L2)
BLACK (NOW PHASE!)
Phase 3 (L3)
GREY
Neutral (N)
BLUE (NOW NEUTRAL!)
Protective Earth (CPC)
GREEN / YELLOW
CRITICAL SAFETY & EXAM TRAP: In older installations, BLACK was Neutral and BLUE was Phase 3. In modern installations, BLACK is Phase 2 (Live!) and BLUE is Neutral! Connecting an old black neutral to a new black phase causes an immediate catastrophic 400V dead-short! Whenever old and new colours mix, a Regulation 514.14 Dual Colour Warning Notice is mandatory!